ProREZ Coatings, LLC
P.O. Box 153, Cromwell, CT 06416-0153
860.436.2070 www.prorezcoatings.comSafety Data Sheet
Date Issued: 9/16/25 Version: 2.0
1. CHEMICAL PRODUCTS AND COMPANY IDENTIFICATION
Product Names/Trade Names: ProWear, ProWear+, ProGrit 54, ProGrit 36
Chemical Family: Aluminum Trihydratye, Boehmite
Manufacturer’s Name: ProREZ Coatings, LLC
PO BOX 153
Cromwell, CT 06416-0153 USA
General No.:(860) 436-2070 (8:00am to 5:00pm Eastern Time)
Company 24 Hour Emergency Response Information: CHEMTEL: 1-800-255-3924
Emergency telephone numbers are to be used only in the event of chemical emergencies involving a spill, leak, fire,
exposure, or accident involving chemicals. All non-emergency questions should be directed to customer service.
2. HAZARDS IDENTIFICATION
Emergency Overview: Caution! The toxicological properties of this material have not been fully investigated. May
cause eye and skin irritation. May cause respiratory and digestive tract irritation. Target Organs: No data found.
NON HAZARDOUS; NON DANGEROUS GOODS
Non-dangerous goods for transport according to the ADG code.
Non-hazardous according to the criteria in the Hazardous Substances (Minimum Degrees of Hazard) regulations
2001 and NOHSC
Classification of the substance
Eye Irritation 2B H320 Causes eye irritation
Label Elements
Hazardous components that must be listed on the label: Not Required
Signal word: Not Required
Pictograms:
Hazard Statements:
H320 Causes eye irritation
H315 Causes skin irritation
ProWear, ProGrit 1 of 6
Safety Data Sheet
Precautionary Statements
P264 Wash exposed areas thoroughly after handling
P305+P351+P338 If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present
and easy to do. Continue rinsing.
P337+P313 If eye irritation persists: Get medical advice/attention.
P303+P352 IF ON SKIN (or hair): Wash with plenty of soap and water.
Repeated exposure may results in slightly hazardous in case of skin contact (irritant), of eye contact (irritant), of
ingestion, of inhalation.
General Information: This product contains no listed carcinogens according to IARC, ACGIH, NTP and/or OSHA
in concentrations of 0.1 percent or greater. Prolonged contact may result in chemical burns and permanent damage.
Repeated or prolonged contact causes sensitization, asthma and eczemas.
Read the entire SDS for a more thorough evaluation of the hazards.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients % By Weight CAS Number
Aluminum Oxide >99.9% 1344-28-1
4. FIRST-AID MEASURES
General advice: Seek medical advice or medical attention if condition persists.
Eye contact: Rinse immediately with plenty of water for at least 15 minutes.
Skin contact: Immediately remove any extraneous chemical, if possible without delay. Take off contaminated
clothing and shoes immediately. Wash body off with soap and plenty of water.
Ingestion: Rinse mouth. Drink plenty of water. Never give anything by mouth to an unconscious person. If a person
vomits when lying on his back, place him in the recovery position and turn victim’s head to the side. Do not induce
vomiting.
Inhalation: Move to fresh air. If breathing has stopped or is labored, give assisted respirations. Supplemental
oxygen may be indicated. If the heart has stopped, trained personnel should begin cardiopulmonary resuscitation
immediately.
Notes to Physician: No specific treatment. Treat symptomatically.
5. FIRE-FIGHTING MEASURES
Suitable Fire Extinguishing Media: Water fog, foam, dry chemical, carbon dioxide.
Special Exposure Hazards: Promptly isolate the scene by removing all persons from the vicinity of the incident
if there is a fire. No action shall be taken involving any personal risk or without suitable training. Fire water
contaminated with this material must be contained and prevented from being discharged to any waterway, sewer
or drain.
ProWear, ProGrit 2 of 6
Safety Data Sheet
Special Protective Equipment for Fire-Fighters: Fire-fighters should wear appropriate protective equipment and
self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Danger of Explosion: This product does not present an explosion hazard
Flammable Limits: Not Available
Explosion Limits: Not Available
Auto-Ignition: Not Available
Flash Point: Not Available
6. ACCIDENTAL RELEASE MEASURES
Personal Precautions: No No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk
through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator
when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8).
Environmental Precautions: Water polluting material. May be harmful to the environment if released in large
quantities. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform
authorities if the product has caused environmental pollution (sewers, drains, waterways or soil). .
Methods for Cleaning up: Stop leak if without risk. Move containers from spill area. Approach release from
upwind. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or
diatomaceous earth and place in container for disposal according to local regulations (see section 13). Contaminated
absorbent material may pose the same hazard as the spilled product. Note: see section 1 for emergency contact
information and section 13 for waste disposal.
7. HANDLING AND STORAGE
Handling: Put on appropriate personal protective equipment, PPE (see Section 8). Eating and drinking should be
prohibited in areas where this material is handled, stored and processed. Remove contaminated PPE or clothing,
wash hands and face before eating and drinking. Use only in area provided with appropriate exhaust ventilation. Do
not get in eyes, skin or clothing. Do not ingest. Normal cleanup procedures. Cares should be taken to avoid causing
dust to become airborne. Vacuum cleaning systems are recommended.
Storage: Stored in cool, dry, ventilated area. Keep material tightly sealed. Avoid breakage of bagged material or
spills of bulk material. Use dustless methods (vacuum) and place into closable container for disposal, or flush with
water. Do not dry sweep.
8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
Special Note for Exposure Control: Consult local authorities for acceptable exposure limits.
OSHA PEL (TWA): 15 mg/m3 total dust, 5 mg/m3 respirable fraction
ACGIH TLV (TWA): 10 mg/m3 inhalable (total) particulate matter containing no asbestos and <1% crystal silica, A4
ProWear, ProGrit 3 of 6
Safety Data Sheet
Engineering measures: Work in well-ventilated area. Provide natural or explosion-proof fan to ensure adequate
ventilation, especially in confined area. Avoid contact with skin, eyes, and clothing.
Environmental exposure controls: Construct a dike to prevent spreading. Emissions from ventilation or work
process equipment should be checked to ensure they comply with the requirements of environmental protection
legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be
necessary to reduce emissions to acceptable levels.
Hygiene Measures: Wash hands, forearms and face thoroughly after handling chemical products, before eating and
drinking, smoking or using the lavatory and at the end of the working period. Contaminated work clothing should not
be allowed out of the workplace. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Personal Protection:
Respiratory - In case of inadequate ventilation wear respiratory protection. Respirator selection must be based
on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected
respirator.
Eyes – Splash proof safety glasses.
Skin - Rubber or plastic apron. Rubber or plastic gloves. Long sleeved clothing or wear protective sleeves. Remove
and wash contaminated clothing before re-use.
Other protective equipment information - Chemical-resistant, impervious gloves complying with an approved
standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary.
Neoprene gloves. PVC disposable gloves. Nitrile rubber. Butyl rubber. Impervious gloves. (The breakthrough time of
the selected glove(s) must be greater than the intended use period.)
9. PHYSICAL AND CHEMICAL PROPERTIES
Form: Solid
Odor: None
Color: White
PH Value: Not Available
Boiling Point: Not Available
Melting Point: Not Available
Vapor Pressure (25ºC): Not Available
Vapor Density: Not Available
Density (Nominal): 33.00 lb/US gallon
Solubility in water: Negligible
Evaporation Rate (Butyl Acetate = 1): Not Available
Volatile Organic Compounds: Not Available
ProWear, ProGrit 4 of 6
Safety Data Sheet
10. STABILITY AND REACTIVITY
Chemical stability: Stable under normal conditions. Hazardous reactions will not occur.
Conditions to avoid: No specific data.
Materials to avoid: No specific data.
Hazardous decomposition products: No specific data.
Hazardous polymerization: Under normal conditions hazardous polymerization will not occur.
11. TOXICOLOGICAL INFORMATION
Routes of Entry: Absorbed through skin. Eye contact. Ingestion.
Toxicity to Animals: LD50: Not available. LC50: Not available.
Chronic Effects on Humans: Not available.
Other Toxic Effects on Humans: Slightly hazardous in case of skin contact (irritant), of ingestion, of inhalation.
12. ECOLOGICAL INFORMATION
Environmental Effects: No known significant effects or critical hazards.
Ecotoxicity: Not available.
BOD5 and COD: Not available.
13. DISPOSAL CONSIDERATIONS
Waste Disposal: Dispose in accordance with federal, state and local regulations.
The generation of waste should be avoided or minimized wherever possible. Empty containers should be taken to
an approved waste-handling site for recycling or disposal. Incineration or landfill should only be considered when
recycling is not feasible. Care should be taken when handling emptied containers that have not been cleaned or rinsed
out. Empty containers or liners may retain some product residues. Refer to 40 CFR § 261.7 (residues of hazardous
waste in empty containers).
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
14. TRANSPORT INFORMATION
Regulatory UN number Classes Packing Group Proper
information Shipping Name
DOT Not Regulated
TDG Not Regulated
IMDG Not Regulated
IATA Not Regulated
ProWear, ProGrit 5 of 6
Safety Data Sheet
15. REGULATORY INFORMATION
Country Regulatory List Notification
USA TSCA Included on Inventory
EU EINECS Included on Inventory
Canada DSL Included on Inventory
China SEPA Included on Inventory
Japan ENCS Included on Inventory
OSHA - This product is considered non-hazardous.
SARA 302/304/311/312 extremely hazardous substances – No ingredients listed.
SARA 311/312 Hazard Identification - No ingredients listed.
SARA 313 - No ingredients listed.
U.S. State Regulations:
California Safe Drinking Water & Toxic Enforcement Act (Proposition 65) - This product does not contain any
chemicals known to State of California to cause cancer, birth defects or any other reproductive harm.
Canada WHMIS – This product is considered non-hazardous.
This product has been classified in accordance with the hazard criteria of the Controlled Products
Regulations and the SDS contains all the information required by the Controlled Products Regulations.
16. OTHER INFORMATION
Hazardous Material Information System (HMIS):
Scale 0-4 NFPA HMIS
4=Severe Hazard Health 1 1
3=Serious Hazard Flammability 0 0
2=Moderate Hazard Reactivity 0 0
1=Slight Hazard
0=Minimal Hazard
THE INFORMATION AND RECOMMENDATIONS PRESENTED HEREIN ARE ACCURATE TO THE BEST OF OUR
KNOWLEDGE. USER MUST CONDUCT THEIR OWN TESTS TO DETERMINE THE SUITABILITY OF THESE PRODUCTS
FOR THEIR PARTICULAR PURPOSES AND USAGE. BECAUSE OF NUMEROUS FACTORS AFFECTING RESULTS, PROREZ
COATINGS, LLC AND ITS AFFILIATION MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR PURPOSE, OTHER THAN MATERIAL CONFORMS TO OUR
APPLICABLE CURRENT SPECIFICATIONS. PROREZ COATINGS, LLC ASSUMES NO LEGAL RESPONSIBILITY FOR USE
OR RELIANCE ON THE INFORMATION CONTAINED IN THIS SAFETY DATA SHEET.
END OF DATA SHEET
ProWear, ProGrit 6 of 6