zyp-bn-lubricoat-coleparmer

Original PDF document published by Not stated.

Publisher: Not stated
Document type: PDF document
Material: Not stated
CAS: Not stated
Product code: Not stated
Language: Not stated
Revision: Not stated
Region: Not stated
Pages: 5

Full document text

5 pages · Original document language · 5 OCR pages

Text extracted from the original PDF. Page order and original wording are preserved; tables and symbols may differ from the PDF layout. OCR text may contain recognition errors. Check the original PDF for safety-critical details.

Page 1 · OCR

Product: Boron Nitride Lubricoat

aur oun

1 0 0 **

MATERIAL SAFETY DATA SHEET

SECTION I: PRODUCT AND COMPANY IDENTIFICATION

EFFECTIVE DATE: April 11, 2014

PRODUCT NAME: Boron Nitride Lubricoat

MANUFACTURER: ZYP Coatings, Inc. 120 Valley Court Oak Ridge, TN 37830

Manufacturer Phone: (865) 482-5717 (8:30 a.m. - 5 p.m.) Manufacturer Fax: (865) 482-1281

For any chemical emergency, call Chem-Tel: 800-255-3924, outside the U.S., call COLLECT 813-248-0585

SECTION II: COMPOSITION/INFORMATION ON INGREDIENTS

(SEE SECTION VII] FOR EXPOSURE GUIDELINES)

COMPONENT CAS NUMBER % BY WEIGHT Boron Nitride 10043-11-5 23-28

Water 7732-18-5 65-70 Aluminum Oxide 1318-23-46 3-5

SECTION Ill: HAZARDS IDENTIFICATION

EMERGENCY OVERVIEW

Nearly odorless white non-flammable water-based paint of Boron Nitride. Mildly acidic with pH between 2 and 4. Slippery, can cause falls if walked on. The paint is mildly corrosive to the eyes on contact. Inhalation of paint mist or fumes evolved upon first heating of coating to 600°C may be irritating to respiratory tract.

POTENTIAL HEALTH EFFECTS:

PRIMARY ROUTES OF EXPOSURE: Inhalation and contact to the eyes. TARGET ORGANS: Eyes, skin and respiratory system.

EYE: Corrosive burns upon extended contact.

Page 2 · OCR

SKIN CONTACT: Possible mild skin inflammation. SKIN ABSORPTION: N/A

INGESTION: Irritation to gastrointestinal tract. INHALATION: Irritation to upper respiratory system.

ACUTE EFFECTS: The paint may be mildly corrosive to the eyes on contact, and irritating to the skin on prolonged contact. Mists from the product are irritating to the upper respiratory system as well as the fumes that are emitted during the first heating of the coating to 600°C.

CHRONIC EFFECTS: Excessive inhalation of dust above TLV of dried materials over long periods of time may cause industrial bronchitis, reduced breathing capacity and lead to increased susceptibility to lung disease.

CARCINOGENICITY: Not Carcinogenic

SECTION IV: FIRST AID MEASURES

EYES: Flush eyes, including under the eyelids, with large amounts of water. If irritation persists, seek medical attention.

SKIN: Wash thoroughly with mild soap and water.

INGESTION: Give copious amounts of water and seek medical attention. INHALATION: Remove to fresh air. Seek medical attention if symptoms persist.

SECTION V: FIRE FIGHTING MEASURES

GENERAL OVERVIEW

This water-based refractory coating is non-combustible. Use extinguishing media appropriate to the surrounding fire.

FLASH POINT: N/A

METHOD USED: N/A

FLAMMABLE LIMITS: LFL: N/A UFL: N/A

EXTINGUISHING MEDIA: N/A

UNUSUAL FIRE & EXPLOSIVE HAZARDS: See additional notes

FIRE FIGHTING EQUIPMENT: N/A

ADDITIONAL NOTES: Initial exposure to high temperatures evolve in small amounts fumes that may be irritating or corrosive to the upper respiratory system.

Page 3 · OCR

SECTION VI: ACCIDENTAL RELEASE MEASURES

Contain the spill by using a mineral absorbent. It can be readily neutralized using any basic neutralization agent such as lime or sodium carbonate. Clean-up personnel should wear rubber gloves and goggles to prevent irritation from contact.

SECTION VII: HANDLING AND STORAGE

Store in original container. Do not store in metal containers since the paint may be corrosive to the container. Boron nitride is slippery and is a slip hazard on walkways. Practice good housekeeping. Note Exposure Controls and Personal Protection (Section VII!) before using.

SECTION Vill: EXPOSURE CONTROL/PERSONAL PROTECTION

INGREDIENT CAS NUMBER EXPOSURE LIMIT

Boron Nitride 10043-11-5 None established (treat as nuisance dust); Total dust 10 mg/m’, Respirable 5 mg/m?

Aluminum Oxide 1318-23-6 ACGIH Total dust 10 mg/m*, Respirable dust 5 mg/m?

Nitric Acid 7697-37-2 OSHA TWA= 2ppm, 5 mg/m?, STEL-4 ppm, 10 mg/m?

The TLV:TWA calculated for dust generated from the dried product is 10 mg/m’ for total dust and 5 mg/m? for respirable dust. The TLV: TWA for dust generated from this mixture is calculated using the general formula given in ACGIH adopted Appendix C, Subpart A2, threshold limit values for mixtures of mineral dust.

SPRAY APPLICATIONS: For spray application where exposure exceeds TLV use a NIOSH/MSHA approved respirator, goggles, rubber gloves, and protective clothing.

VENTILATION: Provide adequate general ventilation and local ventilation to contro! mist/dusts below the TLV.

PERSONAL PROTECTION: Glasses, gloves and long sleeve clothing.

SECTION IX.: PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE: White slurry ODOR: Nearly odorless

paint

PHYSICAL STATE: Liquid pH: 2-4

VAPOR PRESSURE: VAPOR DENSITY: Less than

Approx. 10-20mmHg air (Air=1)

BOILING POINT: 212°F FREEZING POINT: 30°F

SOLUBILITY IN WATER: N/A Seen GRAVITY: 1.12 VISCOSITY: Approx. 900-

. 1200

VOC CONTENT: 0 gil Brookfield Spindle 3 / Speed

PERCENT VOLATILE: 65-70% EVAPORATION RATE: About

Page 4 · OCR

that of water

SECTION X: STABILITY AND REACTIVITY

STABILITY: This refractory coating is stable under all normal conditions of storage. Hazardous polymerization will not occur.

INCOMPATIBILITY: Do not mix with alcohols. As a good practice, do not mix with any other materials.

HAZARDOUS DECOMPOSITION PRODUCTS: Upon initial heating to 600°C will yield very small amounts of nitric oxide fumes.

SECTION XI: TOXICOLOGICAL INFORMATION

Please see Section Vill. For available information.

SECTION XII: ECOLOGICAL INFORMATION

None Available

SECTION XiIli: DISPOSAL CONSIDERATIONS

Consult local, state and federal regulations for compliance. The low pH and liquid nature of this paint product may restrict disposal options. Non-contaminated paint may be returned to the

manufacturer for proper disposal. The dried paint generally does not exhibit any characteristics of a hazardous waste.

SECTION XIV: TRANSPORTATION INFORMATION

DOT Class: Not regulated

SECTION XV: REGULATORY INFORMATION

This product contains less than 1% nitric acid CAS# 7697-37-2. RQ = 1000 Ibs, TPQ = 1000 Ibs.

Nitric acid is on the following regulatory lists:

Clean Water Act Section 311 Hazardous Substances

Comprehensive Environmental response, Compensation, and Liability Act (CERCLA) Hazardous Substances

Superfund Amendments and Reauthorization Act (SARA) Title III

Section 302 Extremely Hazardous Substances

Section 313 Toxic Substances

Section 110 Priority List of CERCLA Hazardous Substances

OSHA Air Contaminants

Canadian WHMIS Disclosure List

Massachusetts Substance List

New Jersey Right to Know Hazardous Substance List Pennsylvania Hazardous Substance List.

Page 5 · OCR

TSCA INVENTORY: All substances contained in this product are listed in the Toxic Substances Control Act (TSCA) Chemical Substance Inventory.

SECTION XVI: OTHER INFORMATION

Although reasonable care has been taken in the preparation of the information contained herein, the manufacturer extends no warranties, makes no representation and assumes no responsibility as to the accuracy or suitability of such information for application to purchaser's intended purposes or for consequences of its use.

** Caution: HMIS rating are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS ratings are not required on MSDSs under 29 CFR 1910.1200, the preparer may choose fo provide them. HMIS ratings are to be used only in conjunction with a fully implemented HMIS program by workers who have received appropriate HMIS training. HMIS is @ registered trade and service mark of the NPCA. HMIS materials may be purchased exclusively from J.J. Keller (800) 327-6868.